Diagnostic Trouble Code Index DTC: Transfer Case Control Module -- XF/X250

• Diagnostic Trouble Code (DTC) Index DTC: Transfer Case Control Module
  • Description And Operation
    • DTC Transfer Case Control Module (TCCM)
    • DTC B1142-62: Ignition Status 1 - Signal compare failure
      • Possible Causes
      • Action
    • DTC P080A-56: Clutch Position Not Learned - Invalid/incomplete configuration
      • Possible Causes
      • Action
    • DTC P0810-04: Clutch Position Control Error - System internal failures
      • Possible Causes
      • Action
    • DTC P0810-07: Clutch Position Control Error - Mechanical failures
      • Possible Causes
      • Action
    • DTC P0810-56: Clutch Position Control Error - Invalid/incomplete configuration
      • Possible Causes
      • Action
    • DTC P0810-78: Clutch Position Control Error - Alignment or adjustment incorrect
      • Possible Causes
      • Action
    • DTC P170E-92: Clutch Delivered Torque Performance - Performance or incorrect operation
      • Possible Causes
      • Action
    • DTC P173A-64: Clutch Actuator Position Sensor Circuit Range/Performance - Signal plausibility failure
      • Possible Causes
      • Action
    • DTC P175B-00: Transfer Case Clutch Deteriorated - No sub type information
      • Possible Causes
      • Action
    • DTC P175C-00: Transfer Case Fluid Deteriorated - No sub type information
      • Possible Causes
      • Action
    • DTC P215A-62: Vehicle Speed/Wheel Speed Correlation - Signal compare failure
      • Possible Causes
      • Action
    • DTC P2787-98: Clutch Temperature Too High - Component or system over temperature
      • Possible Causes
      • Action
    • DTC U0001-81: High Speed CAN Communication Bus - Invalid serial data received
      • Possible Causes
      • Action
    • DTC U0001-87: High Speed CAN Communication Bus - Missing message
      • Possible Causes
      • Action
    • DTC U0001-88: High Speed CAN Communication Bus - Bus off
      • Possible Causes
      • Action
    • DTC U0300-00: Internal Control Module Software Incompatibility - No sub type information
      • Possible Causes
      • Action
    • DTC U2012-4A: Car Configuration Parameter(s) - Incorrect component installed
      • Possible Causes
      • Action
    • DTC U2100-54: Initial Configuration Not Complete - Missing calibration
      • Possible Causes
      • Action
    • DTC U3000-47: Control Module - Watchdog/safety micro controller failure
      • Possible Causes
      • Action
    • DTC U3000-49: Control Module - Internal electronic failure
      • Possible Causes
      • Action
    • DTC U3000-4B: Control Module - Over temperature
      • Possible Causes
      • Action
    • DTC U3006-13: Control Module Input Power "A" - Circuit open
      • Possible Causes
      • Action
    • DTC U3006-16: Control Module Input Power "A" - Circuit voltage below threshold
      • Possible Causes
      • Action
    • DTC U3006-17: Control Module Input Power "A" - Circuit voltage above threshold
      • Possible Causes
      • Action
    • DTC U3006-62: Control Module Input Power "A" - Signal compare failure
      • Possible Causes
      • Action
    • DTC U3007-13: Control Module Input Power "B" - Circuit open
      • Possible Causes
      • Action
    • DTC U3007-16: Control Module Input Power "B" - Circuit voltage below threshold
      • Possible Causes
      • Action
    • DTC U3007-17: Control Module Input Power "B" - Circuit voltage above threshold
      • Possible Causes
      • Action
    • DTC U3007-62: Control Module Input Power "B" - Signal compare failure
      • Possible Causes
      • Action