Service Information: Precautions: Precaution

Download the full database via torrent (~1.1 TB) | Download Brad's custom LEMON patches

Always use a 12 V battery as power source .
Never attempt to disconnect battery cables while engine is running .
Before connecting or disconnecting the ECM harness connector, turn ignition switch OFF and disconnect negative battery cable. Failure to do so may damage the ECM because battery voltage is applied to ECM even if ignition switch is turned OFF .
Before removing parts, turn ignition switch OFF and then disconnect negative battery cable .

Fig 1: Disconnecting Negative Battery Terminal
Courtesy of NISSAN NORTH AMERICA, INC.
Never disassemble ECM .
If battery cable is disconnected, the memory will return to the initial ECM values .
The ECM will now start to self-control at its initial values. Engine operation can vary slightly in this case. However, this is not an indication of a malfunction. Never replace parts because of a slight variation .
If the battery is disconnected, the following emission-related diagnostic information will be lost within 24 hours .

Diagnostic trouble codes
1st trip diagnostic trouble codes
Freeze frame data
1st trip freeze frame data
System readiness test (SRT) codes
Test values

Fig 2: Identifying ECM
Courtesy of NISSAN NORTH AMERICA, INC.
When connecting ECM harness connector, fasten (B) it securely with a lever (1) as far as it will go as shown in the figure .
- ECM (2)
- Loosen (A)
Fig 3: Checking Loosen And Fasten ECM Harness Connectors
Courtesy of NISSAN NORTH AMERICA, INC.
- When connecting or disconnecting pin connectors into or from ECM, take care not to damage pin terminals (bend or break) .
  Make sure that there are not any bends or breaks on ECM pin terminal, when connecting pin connectors .
- Securely connect ECM harness connectors .
  A poor connection can cause an extremely high (surge) voltage to develop in coil and condenser, thus resulting in damage to ICs .
- Keep engine control system harness at least 10 cm (4 in) away from adjacent harness, to prevent engine control system malfunctions due to receiving external noise, degraded operation of ICs, etc .
- Keep engine control system parts and harness dry .
- Before replacing ECM, perform "ECM Terminals and Reference Value" inspection and make sure ECM functions properly. Refer to "ECM TERMINAL AND REFERENCE VALUE ".
  
  Fig 4: Identifying Bend And Break Connector Pin
  Courtesy of NISSAN NORTH AMERICA, INC.
  
  Fig 5: Precaution Before Replacing Electronic Control Unit
  Courtesy of NISSAN NORTH AMERICA, INC.
- Handle mass air flow sensor carefully to avoid damage .
- Never disassemble mass air flow sensor .
- Never clean mass air flow sensor with any type of detergent .
- Never disassemble electric throttle control actuator .
- Even a slight leak in the air intake system can cause serious incidents .
- Never shock or jar the camshaft position sensor (PHASE), crankshaft position sensor (POS) .
- After performing each TROUBLE DIAGNOSIS, perform DTC Confirmation Procedure or Overall Function Check. The DTC should not be displayed in the DTC Confirmation Procedure if the repair is completed. The Overall Function Check should be a good result if the repair is completed .
  
  Fig 6: Identifying Malfunction Indicator Lamp
  Courtesy of NISSAN NORTH AMERICA, INC.
- When measuring ECM signals with a circuit tester, never allow the two tester probes to contact .
  Accidental contact of probes will cause a short circuit and damage the ECM power transistor .
Fig 7: Caution For Checking Input And Output Signals Of Control Unit
Courtesy of NISSAN NORTH AMERICA, INC.
Never operate fuel pump when there is no fuel in lines .
- Fuel level sensor unit and fuel pump (1)
- Fuel pressure regulator (2)
- Fuel level sensor (3)
- Fuel tank temperature sensor (4)
Tighten fuel hose clamps to the specified torque .

Fig 8: Identifying Fuel Pump, Fuel Pressure Regulator, Fuel Level Sensor And Fuel Tank Temperature Sensor
Courtesy of NISSAN NORTH AMERICA, INC.
Never depress accelerator pedal when starting .
Immediately after starting, Never rev up engine unnecessarily .
Never rev up engine just prior to shutdown .

Fig 9: Caution For Depressing Accelerator Pedal When Starting
Courtesy of NISSAN NORTH AMERICA, INC.
When installing C.B. ham radio or a mobile phone, be sure to observe the following as it may adversely affect electronic control systems depending on installation location .
- Keep the antenna as far as possible from the electronic control units .
- Keep the antenna feeder line more than 20 cm (8 in) away from the harness of electronic controls .
  Never let them run parallel for a long distance .
Adjust the antenna and feeder line so that the standing-wave radio can be kept smaller .
Be sure to ground the radio to vehicle body .

Fig 10: Identifying C.B. Ham Radio

Courtesy of NISSAN NORTH AMERICA, INC.