Brad's Car Manuals: A 3rd party mirror of CHARM + LEMON car manuals
Home >> Subaru >> 2014 >> XV Crosstrek Limited >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Transmission Control Systems >> Select Lever >> Installation

Select Lever: Installation

Download the full database via torrent (~1.1 TB)  |  Download Brad's custom LEMON patches
  1. Set the select lever assembly to the vehicle body.
  2. Tighten the four mounting bolts to attach the select lever assembly to the vehicle body.

    Tightening torque: 

    18 N.m (1.8 kgf-m, 13.3 ft-lb) 

    Fig 1: Locating Select Lever Assembly Mounting Bolt
    G08550575Courtesy of SUBARU OF AMERICA, INC.
  3. Connect the harness connector.
    Fig 2: Identifying Select Lever Assembly Harness Connector
    G08550574Courtesy of SUBARU OF AMERICA, INC.
  4. Install the harness clip to the select lever assembly.
    Fig 3: Locating Select Lever Assembly Harness Clip
    G08550573Courtesy of SUBARU OF AMERICA, INC.
  5. Install the panel center LWR LH and RH. < Ref. to INSTALLATION , Console Box.>
  6. Shift the select lever to "N" range.
  7. Install the blind A to the housing.
    NOTE: The blind A should be installed so that it is securely caught inside the tab of the housing.
    Fig 4: Identifying Select Lever Assembly Blind A Tab
    G08317540Courtesy of SUBARU OF AMERICA, INC.
  8. Install the blind B behind the blind A.
    Fig 5: Identifying Select Lever Assembly Blind A And B
    G09487580Courtesy of SUBARU OF AMERICA, INC.
  9. Install the housing.
    Fig 6: Identifying Select Lever Housing
    G08317531Courtesy of SUBARU OF AMERICA, INC.
  10. Install the indicator cover, then connect the connector.
    Fig 7: Identifying Select Lever Assembly Indicator Cover
    G08317530Courtesy of SUBARU OF AMERICA, INC.
  11. Install the cover shift lever.
    Fig 8: Identifying Shift Lever Cover Assembly
    G08317529Courtesy of SUBARU OF AMERICA, INC.
  12. Accessing from the button side of the grip, attach the clamp grip pin.
    Fig 9: Installing Selector Lever Clamp Grip Pin
    G08317545Courtesy of SUBARU OF AMERICA, INC.
  13. Install the cover grip AT securely.
    NOTE: After installation, check that the cover grip AT cannot be detached.
    Fig 10: Installing Selector Lever Cover Grip AT
    G08317546Courtesy of SUBARU OF AMERICA, INC.
  14. Insert the grip assembly to the select lever and press it down until a click is heard.
    Fig 11: Inserting Grip Assembly To Select Lever
    G08317547Courtesy of SUBARU OF AMERICA, INC.
  15. After installation of grip, check the following points.
    • The grip will not come off.
    • The button on the grip operates normally.
  16. Install the console box. < Ref. to INSTALLATION , Console Box.>
  17. Shift the select lever to "N" range.
  18. Lift up the vehicle.
  19. Secure the cable to the bracket. < Ref. to INSTALLATION , Select Cable.>
  20. Adjust the select cable position. < Ref. to ADJUSTMENT , Select Cable.>
  21. After adjustment, confirm that the select lever operates properly at all range positions using the shift lock release button.
  22. Install the center exhaust cover.

    Tightening torque: 

    18 N.m (1.8 kgf-m, 13.3 ft-lb) 

    Fig 12: Identifying Center Exhaust Cover
    G08550562Courtesy of SUBARU OF AMERICA, INC.
  23. Install the center exhaust pipe. < Ref. to INSTALLATION , Center Exhaust Pipe.>
  24. Lower the vehicle.
  25. Connect the battery ground terminal. < Ref. to BATTERY , NOTE, Note.>
  26. Inspect the following items. If a malfunction is found in the inspection, adjust the select cable or inhibitor switch.
    1. The shift lock operates normally. < Ref. to SHIFT LOCK OPERATION , INSPECTION, AT Shift Lock Control System.>
    2. Engine starts when the select lever is in "P" or "N" range, but not in other ranges.
    3. Back-up light illuminates when the select lever is in the "R" range, but not in other ranges.
    4. Select lever and indicator positions are matched.