Charging Systems: Generator: Reassembly

Download the full database via torrent (~1.1 TB) | Download Brad's custom LEMON patches

INSTALL GENERATOR ROTOR ASSEMBLY
1. Place the drive end frame on the clutch pulley.
2. Install the generator rotor assembly to the drive end frame.
  
  Fig 1: Locating Generator Rotor Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Place a new generator washer on the generator rotor.
  
  Fig 2: Locating Generator Washer
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL GENERATOR COIL ASSEMBLY
1. Using a deep socket wrench (21 mm) and a press, slowly press in the generator coil assembly.
  
  Fig 3: Pressing Generator Coil Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the 4 bolts.
  Torque: 5.8 N*m (59 kgf*cm, 51 in.*lbf)
  
  Fig 4: Locating Generator Coil Assembly Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL GENERATOR BRUSH HOLDER ASSEMBLY
1. While pushing the 2 brushes into the generator brush holder assembly, insert a Ø1.0 mm (0.039 in.) pin into the brush holder hole.
  
  Fig 5: Inserting Pin Into Brush Holder Hole
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the brush holder assembly to the generator coil with the 2 screws.
  Torque: 1.8 N*m (18 kgf*cm, 16 in.*lbf)
3. Pull out the pin from the generator brush holder.
  
  Fig 6: Locating Brush Holder Assembly Screws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL GENERATOR TERMINAL INSULATOR
1. Install the terminal insulator to the generator coil.
  NOTE: Pay attention to installation direction of the terminal insulator.
  
  Fig 7: Locating Terminal Insulator
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL GENERATOR REAR END COVER
1. Install the generator rear end cover to the generator coil with the 3 nuts.
  Torque: 4.6 N*m (47 kgf*cm, 41 in.*lbf)
INSTALL GENERATOR CLUTCH PULLEY
1. Temporarily install the clutch pulley onto the rotor shaft.
  
  Fig 8: Locating End Cover Nuts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Set SST (A) and (B).
  SST 09820-63020
  
  Fig 9: Setting Rotor Shaft To SST
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Clamp SST (A) in a vise.
  NOTE: Be sure to fix the flat surface of SST (A) in a vise.
  
  Fig 10: Clamping SST In Vise
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Place the rotor shaft end into SST (A).
  
  Fig 11: Placing Rotor Shaft End Into SST
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Fit SST (B) to the clutch pulley.
  
  Fig 12: Fitting SST To Clutch Pulley
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Tighten the pulley by turning SST (B) in the direction shown in the illustration.
  Torque: without SST 110 N*m (1125 kgf*cm, 81 ft.*lbf) with SST 84 N*m (857 kgf*cm, 62 ft.*lbf)
  NOTE:
  - Use a torque wrench with a fulcrum length of 318 mm (12.52 in.).
  - This torque value is effective when SST is parallel to a torque wrench.
  - Hold the generator assembly tightly.
  Fig 13: Tightening Pulley By Turning SST
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Remove the generator assembly from SST.
8. Check that the clutch pulley rotates smoothly.
9. Install a new clutch pulley cap to the clutch pulley.